Minwax 43010 Polyurethane Satin Finish, 1 Pint

Dissolves varnish, lacquer, and shellac Will not destroy the patina or natural color of wood Will not raise the grain or loosen glue joints, veneers, inlays, wood filters, or laminated woods.

Features:-

• Clear; hardest of protective coatings
• Long-lasting beauty in finished and unfinished wood
• Use natural bristle brush for application
• Interior wood finish only
• Cleans up with mineral spirits
• Covers 175 - 200 sq ft per quart
• 2 - 3 coats recommended
• Dries in 8 hours

Warning:-

Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup.

Directions:-

1. Surface must be dry and free of old finishes in poor condition, paint, wax, grease, polish, dirt or other foreign matter.
2. Sand to obtain a smooth uniform surface. Remove all dust with a cloth dampened with mineral spirits.
3. Stir Minwax Fast-Drying Polyurethane before and during use to eliminate settling on the bottom of the can. Stir in such a manner as to rotate the product from the bottom to the top of the can. NEVER SHAKE.
4. Apply a THIN coat of Minwax Fast-Drying Polyurethane using a high-quality natural or foam brush.
5. Let dry 4-6 hours. Then lightly sand entire surface with fine sandpaper (220 grit) to ensure an even finish and proper adhesion. Remove all dust.
6. Apply second coat. If third coat is desired, repeat step 5 before application.
7. After final coat, allow 24 hours before light use.

When used on wooden floors, use a lambs wool or synthetic pad applicator or natural bristle brush and maintain a wet edge to avoid lap marks. For maximum durability, we recommend three coats. Avoid heavy traffic and replacing of furniture for 72 hours after final coat. When replacing furniture, do not slide. Do not install rugs or clean floors for 7 days.

CLEAN-UP: For easy clean-up use mineral spirits or paint thinner.

COVERAGE: Approximately 125 square feet per quart.

FAQ:-

Q. What is the best way to select a sheen?

Sheen choice is a personal preference. Satin sheens reflect less light and gloss sheens reflect more light.

Q. Is one sheen more durable than the others?

No. The additives that distinguish satin from semi-gloss and gloss do not compromise the durability of the finish.

Q. What can be done to avoid bubbles in the finish?

There are four ways. First, stir, don't shake, the can. Second, use a high-quality, natural bristle brush. Third, work the finish into the wood, but don't create excess foam. Fourth, "tip-off" the finish before stopping, carefully running the brush at a 45-degree angle the length of each board in one unbroken movement. This will burst and smooth out any bubbles that may have been created.

Q. Should Minwax Fast-Drying Polyurethane be sanded between coats?

Yes. A light sanding (#220 sandpaper) will remove any fine particles of dust that have settled on the finish while it was still wet. Light sanding also helps abrade the surface, improving intercoat adhesion.

Q. Why does Minwax Fast-Drying Polyurethane sometimes take longer to dry than the instructions indicate?

The drying time is affected by the amount of moisture in the air, the air temperature and the thickness of the coats. When humidity is high, temperature is low, or coats are thick, it takes longer for the film to dry.

Q. What is the best way to determine how many coats of Minwax Fast-Drying Polyurethane to apply?

If you look closely at the wood in bright, direct light, you should not be able to detect any dry spots. If you do, an additional coat is necessary to protect the wood.

Q. Does Minwax Fast-Drying Polyurethane need to be waxed?

No. Wax does provide an extra layer of protection, but it will prevent you from applying an additional coat of Minwax Fast-Drying Polyurethane in the future without first removing the wax. Instead, we recommend using Minwax Wood Cabinet Cleaner to keep wood clean and looking beautiful.